Jewel Nath
← Home

Pi Car

A Raspberry Pi 3 car with several driving modes: it follows a line, avoids obstacles, stops at a table’s edge, has a simple follow mode, and drives from the keyboard or from a panel with its camera’s live video.

Built2022 – 2023My part: built and coded by me alone, as my university project at Comilla University

What it shows

Driving modes
Line following with IR sensors, obstacle avoidance with an ultrasonic sensor on a servo, an edge stop and a follow mode
Live video control
A window with the camera’s live video and four arrow buttons, used through VNC from a phone or a laptop
Hardware from Python
Motors, three servos, the ultrasonic and IR sensors and a buzzer, all on the Raspberry Pi’s GPIO pins
A solo build
From a wooden chassis on 18 April 2022 to clear acrylic by 4 May, built and coded by me

Built · Apr – Jun 2022

A Raspberry Pi on wheels

Four geared motors carry a clear acrylic body, with a Raspberry Pi 3 on top. At the front, the camera looks around on two servos and an ultrasonic sensor turns on a third; under the nose, an IR board watches the floor.

Avoiding obstacles · May 2022

In video

Short silent clips. Tap one to play it.

On the desk and the track

  • May 2022

    Following a tape line on the floor with its IR sensors

  • May 2022

    Stopping at the edge of the desk when its IR sensors lose the floor, and driving on when it is moved back

  • May 2022

    Driven from the camera panel on a laptop, with the car’s live video on the screen

  • May 2022

    A walk around the car on the desk, just rebuilt on clear acrylic

Upright

  • May 2022

    The follow mode: it drives forward while something is within 15 cm

  • May 2022

    The same line, filmed from above

The build

  1. 18 Apr 2022

    The first build taking shape: a Raspberry Pi 3 and a breadboard on a wooden chassis.

  2. 18 Apr 2022

    Up close: the Pi, the camera on two servos and the wiring.

  3. 18 Apr 2022

    The same night, from the side: four geared motors, the battery pack and the Pi on the top deck.

  4. 4 May 2022

    Rebuilt on clear acrylic, its camera up.

  5. 6 May 2022

    In the dark, its five-sensor line board lit red at the front.

  6. 29 Jun 2022

    Me with the car in the ICT lab at Comilla University, its program on the monitor.

How it works

One Pi, a program per mode

Everything runs on the Raspberry Pi, in Python. Each mode is its own program: two read the IR sensors, two the ultrasonic sensor, one drives from the keyboard, and the panel shows the camera with arrow buttons.

Datasheet

Brain
A Raspberry Pi 3; Python with RPi.GPIO, gpiozero, OpenCV, Tkinter and pygame
Drive
Four geared DC motors on a motor driver
Servos
Three: two point the camera, one turns the ultrasonic sensor
Senses
The Pi camera, an HC-SR04 ultrasonic sensor, and a five-sensor IR board, of which the code reads three
Also
A buzzer
Body
Clear acrylic since May 2022; a wooden chassis before it

Driving modes

Line
Follows a tape line with three IR sensors
Obstacles
Avoids obstacles with the ultrasonic sensor, which a servo turns to look around
Edge stop
Stops when its IR sensors lose the floor at a table’s edge
Follow
Drives forward while something is within 15 cm of the ultrasonic sensor
Keyboard
W and S set the speed, A and D steer, Q stops
Panel
A window with the camera’s live video and four arrow buttons; used from a phone or a laptop through VNC

My part

Built alone, at Comilla University

Pi Car was my university project at Comilla University. I built and coded it alone, mostly in the ICT department’s lab. Two parts of the code follow published examples.

Built on

Both are credited in the car’s repository too.

The code

Read the code

Every mode is in its repository, with its pin map and how to run each mode on a Raspberry Pi.

Next: OrbiBot

At Orbitax, I build OrbiBot in my free time. V1 was a mecanum robot with my own firmware, ROS 2 navigation and an AI agent.